Free Energy Transformer: Combination of Bifilar Coil and Joule Thief Circuit

A standard transformer does not generate free energy, meaning it does not produce output power greater than the input power. This is because, at the secondary coil of the transformer, a reverse electromotive force is created, which hinders the increase of the magnetic flux generated at the primary coil, leading to a decrease in current if the voltage is increasing.

This reverse electromotive force, also known as Lenz's force in the transformer, opposes the increase of the magnetic flux in the primary coil.

The same effect occurs in reverse with a step-down transformer.

However, if the reverse electromotive force is eliminated or exploited, we can create a free energy transformer.

There are many types of free energy transformers. Some of them require expensive materials, so few people dare to invest confidently in them. I will introduce a type of transformer that has a moderate cost.

The purpose of sharing this technology is to help people who are in difficult economic circumstances, especially those who struggle with high monthly electricity bills.

First, you need to be familiar with the Joule Thief circuit and the Bifilar coil. Then, observe and understand the circuit to build your own Free Energy Transformer.

• Bifilar coil: https://overunity-electricity.blogspot.com/p/bifilar-coil.html

• Joule Thief circuit: https://overunity-electricity.blogspot.com/p/eternal-light-from-joule-thief-circuit.html

This is the circuit:

Circuit diagram: Free Energy Transformer - Combination of Bifilar Coil and Joule Thief Circuit

Explanation:

The Joule Thief circuit stops the current when it is increasing and releases a high-voltage pulse, but it immediately cuts off. This continuous process creates a high-frequency voltage at the Bifilar coil terminal.

The circuit is opened and closed based on the operation of the transistor, with the BE pin acting as a continuous open-and-close switch.

The Bifilar coil is the BC coil in the picture.

Two capacitors are connected in parallel across the B and C legs of the transistor, including a variable capacitor, to adjust the voltage and frequency of the Bifilar coil.

Since the coils are special Bifilar coils, there is no reverse electromotive force acting on the primary coil. The output energy will be greater than the input energy. This special secondary coil acts as a capacitor, and the entire circuit will perform better than a conventional free energy toroidal transformer.

The remaining three coils are made from the aluminum foil of a capacitor (from an aluminum electrolytic capacitor). Each CC coil is wound from two aluminum foils in the style of a Bifilar coil. Note: the two aluminum foils are taken from the core of a large electrolytic capacitor and wound on a ferrite core with an insulator between them.

Before winding the wire, use a soldering iron to connect the inner electromagnetic wire. There are two wires in the center and two wires on the outside, similar to the Bifilar coil theory.

Other components include potentiometers, diodes designed as rectifier bridge diodes (4 diodes), variable capacitors, and electrolytic capacitors with high capacitance at the output.

At the grounding point, variable capacitors and electrolytic capacitors are connected in parallel to adjust the output voltage, working in conjunction with the variable capacitor at the input. You adjust until the voltage is suitable.

Because there is no reverse electromotive force and the current is quite large due to the three coils (CC coils), this device can be life-threatening when in operation.

You may also use:

1/ An inverter at the output to adjust the voltage to resemble a sine wave before use.
2/ An Uninterruptible Power Supply (UPS) at the output, which will store energy gradually.
3/ A battery bank to charge, then an inverter.

Doing so will make you completely energy-independent, meaning you won't need to buy electricity from companies anymore.

You should purchase a voltage and current meter to check the output and input. The variable capacitor will adjust the voltage while measuring.

Accessories:

• Ferrite transformer core | OR: at Amazon

• Copper wire | OR: Other link

• Diode

• Resistor

• Polarized capacitor

Additional information on the specifications for making this transformer yourself:

This is a Tesla/joule thief hybrid circuit that its inventor claim to produce 90 times the input power! The circuit can be self looped and can provide 1050W of power. from the 1050W only the 11.6W will loop back to supply the joule thief. If you remove the bridge rectifier and the C capacitor you can use the circuit with high frequency AC output. The circuit uses the 2n3055 and a regular bifilar coil `BC` (45+45 turns, 0.5mm wire) to pulse the ferrite core which consist of two large U shape ferrites. The Coils CC1, CC2 and CC3 are not ordinary coils, Are Capacitor/coils combination.

Those coils are no more than two aluminum foils taken from the guts of a large electrolitic capacitor and winded on the ferrite core with a dielectric insulator between them, Plastic film in that case.  Each Coil/capacitor has 60 turns of foil pairs. Inductunce should be around 0.53mH and the forming capacitance 48μF for each finished coil.

So each coil/capacitor has four terminal ends and not two as a regular capacitor has. Two at start and two at the end.  The circuit use three of these coils for the output. Try to make them as identical as they can be. Capacitors may need to be changed according to the forming capacitance and inductunce of your coils. The two variable capacitors and the variable resistor are needed to tune the circuit to resonate. 

The earth connection must be good and must be completely seperate from the house mains earth.  Start with low power, put 3 volts at the joule thief and gradualy increase the voltage with the load connected.

Tune first the variable resistor for best output,  and then tune the variable capacitors to match the frequencies. Be very carefull while you playing with this unit.  You should be expert in high voltage if you decide to experiment with this circuit. If tuned properly, its output can shock you very badly or even kill you.

Final Words:

This free energy transformer produces output energy much greater than the input—the output is 90 times the input. This transformer is very dangerous to humans, even though the input is only 3V - 30V.

I have not fully explained the operating principle of the transformer based on the physics of Ether electricity, as this is not entirely necessary.

You should ground it properly, with a copper rod longer than 1.5 meters, inserted deep into the ground, then watered and compacted. If not, you can use an electric pole in the power outlet, which is the neutral wire of the power grid. The neutral wire of the power grid will not cause you to lose electricity. Use an electric tester to detect the neutral wire! (The tester does not light up)

Finally, I present a program to create various types of homemade free energy generators, with many different plans corresponding to different technologies:
Generates Energy-On-Demand 👉 Free Energy Will Change Our World Forever

There will be more detailed instructions included in the installation.

Priority will be given to those who purchase the program, and I will offer support via text message for constructing this free energy transformer.

This is shared in light of the current global economic fluctuations. As the New World Order is being established, these fluctuations may influence or relate to your existence here. You may ask yourself: why am I here? The book that answers this question is mentioned in the following video: Tartaria - Radar for Guided Weapons and High Voltage Technology | Tartaria - Tesla Technology

Good luck to you.