Back EMF Exploitation Due To Circuit Breaker of Reed Switch

Scientific Theoretical Basis for Back EMF Mining Generates Free Energy

When a coil is being applied voltage across it, if the circuit is cut off, the magnetic field collapses at nearly the speed of light. The voltage then generated at the ends of the coil is given by

V = Φ/t   

V - The electromotive force which results from the production or consumption of the total magnetic induction Φ (Phi). The unit is the “Volt”

Where t is the time of magnetic field collapse from maximum to complete collapse.

Assuming you have a coil 300000 km long, the magnetic field collapses in about 1 second. Because the velocity of the magnetic field collapse is close to the speed of light.

Since the coil size in the circuit is too small compared to 300000 km, the time t is almost zero.

Therefore, V = Φ/t will reach almost infinity when t ---> 0

Scientific Interpretation V = Φ/t of Ether by Eric P. Dollard:

Very interesting (and dangerous) phenomena manifest themselves when the current path is interrupted, thereby causing infinite resistance to appear. In this case resistance is best represented by its inverse, conductance. The conductance is then zero. Because the current vanished instantly the field collapses at a velocity approaching that of light. As EMF is directly related to velocity of flux, i tends towards infinity. Very powerful effects are produced because the field is attempting to maintain current by producing whatever EMF required. If a considerable amount of energy exists, say several kilowatt hours* (250 KWH for lightning stroke), the ensuing discharge can produce most profound effects and can completely destroy inadequately protected apparatus.

[* The energy utilized by an average household in the course of one day.]

In addition to the way to break the circuit to generate free energy (Overunity) from the Back EMF, there are many other types of Back EMF. See details: Harness the power of Back EMF for Free Energy

The reed switch is an efficient circuit breaker for generating Back EMF. The problem is how to use it to generate free energy.

Note: The formula for calculating voltage Φ/t is based on Ether field physics.

The mathematical formulas for electricity in textbooks, or in mainstream science, are all adapted from those in Ether physics.

That will make you see that many of the formulas in the field of electricity are correct, but feel incomplete, or create paradoxes.

To use the same formulas as the geniuses Tesla or Charles Proteus Steinmetz used for energy corporations, check out the book: A Common Language for Electrical Engineering: Lone Pine Writings by  Eric Dollard

Introducing generators that use reed switches to generate Overunity (free energy) from Back EMF

1. The circuit has a reed switch behind the electromagnet

Circuit design diagram:

Free Energy Generator Circuit Diagram - Harness the power of Back EMF with Circuit Breaker Reed Switch

Note: You may not know the reed switch yet. It's right after the electromagnet in the diagram. An electromagnet is a coil wound around an iron/steel core in the above circuit.

Pictures of Reed Switch:

An image of a real reed switch

Video demonstration of generator operation harnessing the power of Back EMF by circuit breaker by reed switch:

Explain the operation of Overunity generator thanks to Back EMF:

To start, simply apply a voltage of 12 V, with a current of 0.04 to 0.07 A, and let the magnet rotate. With this voltage the reed switch closes.

The permanent magnet on the rotating disc, it has a south pole facing in to promote the electromagnet placed near the reed switch. When the rotating disc with the displacement magnet is aligned with the electromagnet core, the reed switch is open.

When the reed switch is in the open state, the coil with 12V voltage will suddenly increase to a value many times greater than 12V. This new voltage is applied to the 9W LED as shown in the figure, and at the same time is converted to voltage through a transformer. This voltage supplies 36W fluorescent tube lights.

The discharge of a voltage spike spikes in a very short time due to a collapsing magnetic field.

As the disc continues to rotate, the next permanent magnet has a south pole towards the coil (electromagnet), and the process repeats.

The special thing is that the speed of the rotating disc with the magnet is promoted, and the speed of the rotating disc increases gradually. This happens because the increased work of the reed causes the circuit to open, resulting in the coil's magnetic field collapsing in the opposite direction from the direction the DC voltage was initially applied to. So during a very short open circuit of the reed switch, the electromagnet coil will push the Permanent Magnet on the rotating disc. Therefore, the speed of the rotating disk will gradually increase.

Note: The free energy due to Back EMF in the video is real. Because the initial power supplied to the electromagnet coil is very low. Power P = V.I = 12. 0.04 = 0.48 W. However, the output lights up 36W and 9W bulbs.

2. Circuit with reed switch in front of electromagnet

Circuit design diagram:

Here is a circuit diagram with a reed switch that is directly influenced by the magnet

Video demonstration in action:



Working principle: Basically the same as the circuit with the reed switch on the back of the electromagnet (indirectly influenced by the permanent magnet). So I won't go into detail here.

Build a free energy generator for home

Apply the design diagram above to create a generator for the house.

If you use the same layout as above, you can only reduce your electricity bill. Because the output voltage is at high frequency, it will not be suitable for most power consuming devices.

The most basic and simplest solution is to use rectifier bridge diodes to charge the battery bank. Then, from the battery bank will go to the inverter, generating a sinusoidal voltage with the desired frequency. Normally, the common voltage is 110V/ 220V with frequency 50Hz - 60Hz.

I'll update the details on how to do it another time. It's very late at the moment...

There are also many other methods to generate sine waveform voltage with frequency 50 - 60Hz.

Suggest an easy method of generating AC generator:

 Revealed At Last: Ancient Invention Generates Energy-On-Demand

✔ Nikola Tesla’s method of magnifying electric power by neutralizing the magnetic counter-forces in an electric generator

Generates Energy-On-Demand: Easy Power Plan Will Change Our World Forever

✔ Combination of induction motor and alternator 
✔ Combine generators with induction motors - self-powered generators with rotary motion
✔ Various methods of generating high power immobile generators
✔ Or maybe called Overunity for the system. Mother Nature doesn't care about people calling or naming phenomena. Overunity or Free Energy, or Zero Point Energy (ZPE) are just a few different words